Choosing ACSW, AF50M or ACF400M AC Power

November 18, 2026

Start with the load and the test job

“AC power supply” can describe very different jobs. A production engineer may need repeated voltage and frequency steps, a facility may need a specified three-phase conversion, and an avionics bench may need a known 400 Hz output. Choosing by product name alone risks an incorrect phase, voltage reference or power rating. The three ACSOON/Jerrystar options below address those different specifications.

ACSOON ACSW programmable AC source series reference cabinet

ACSOON ACSW series reference photograph. Source: ACSOON programmable power supply. Cabinet configuration and output terminals vary by order.

Three selection paths

RequirementProduct to evaluateCritical check
Repeatable voltage/frequency steps; two loads or circuitsACSW dual-output programmable AC sourceDefine each output, program sequence, simultaneous load and total kVA. The 40–800 Hz and voltage ranges are series references, subject to selected model.
Three-phase frequency conversion for a specified site and loadAF50M-330050 50 kVA converterSpecify input/output voltage and frequency. Its model datasheet confirms 50 kVA designation, three-phase input/output, cabinet and digital display, but does not set a universal conversion direction.
400 Hz AC for avionics bench or electrical checksACF400M-330030 30 kVA 400 Hz sourceNameplate: 380 V ±15% three-phase input, 50/60 Hz, 57 A; 115 V line-to-neutral three-phase output, 400 Hz, 83.3 A.

What each choice solves

ACSW: A test plan can repeat setpoints, rise time and run duration across prototypes or production units. For a dual-output cabinet, document whether one load starts while the other is already operating. The published series reference lists RS-232/RS-485, but verify the exact interface and commands for the quoted model. Do not assume an AC/DC combination or simultaneous operation without a configuration check.

AF50M-330050: A three-phase cabinet is selected around the actual site input and the load's desired output. The “50” in the model is a 50 kVA designation, not a guarantee of 50 kW real power. Give the power factor, inrush and duty cycle. The installed voltage and frequency should appear in the approved quotation and nameplate.

ACF400M-330030: The 30 kVA nameplate gives a concrete 400 Hz test source. The stated 115 V is line-to-neutral, an important distinction in three-phase wiring. Its touchscreen sits behind a hinged cover and the cabinet has a separate emergency stop. The broader ACF400M specification lists other options; do not substitute those series ranges for this photographed unit.

A practical RFQ worksheet

  1. Site supply: nominal and minimum/maximum voltage, frequency, phase, earthing and available upstream protection.
  2. Load: nameplate voltage and current, kVA/kW, power factor, starting current, duty cycle and whether phases are unbalanced.
  3. Output: line-to-neutral versus line-to-line voltage, phase count, neutral, frequency and acceptable tolerance.
  4. Control: manual operation or programmed steps, ramp and dwell time, interface, data to record and stop conditions.
  5. Two-output timing: each circuit's load, start order and simultaneous overlap.
  6. Installation: cabinet dimensions, clearance, ambient conditions, cable length, connector and test documentation.

Jerrystar can use this worksheet to verify a configuration rather than choosing from a broad series table alone. For a complete aircraft external power installation, compare the GPU400 cabinet, which raises additional cable and aircraft connector questions. For the difference between an AC power source and a motor drive, read the AC source vs VFD guide.

FAQ

Can a programmable source replace a dedicated 400 Hz unit? Only if the selected model meets the required voltage, current, frequency, duty cycle and connection. Check the actual operating point and test purpose.

Does AF50M-330050 necessarily convert 50 Hz to 60 Hz? The available model sheet does not specify that exact direction. Define both frequencies and obtain a configuration-specific confirmation.

Can a 115 V line-to-neutral 400 Hz source be treated as any 115 V single-phase supply? No. ACF400M-330030 is specified as a three-phase unit; confirm the wiring, neutral, connector and load before connection.

Do published series maxima apply to every cabinet? No. Series ranges help shortlist options; the quotation and approved technical sheet govern the actual unit.

ACSOON references: ACSW dual-output configuration and AF50W series background (a separate series from AF50M). Send your worksheet to Jerrystar for a model-specific review.

Online Message
Learn about our latest products through SMS or email